Archive for the ‘Boss’ Category

Boss OC-2 Octave

Monday, August 25th, 2014

Boss-OC2

What is it?
Boss OC-2 Octave from compact series. Made in taiwan, april 2001.

Another classic from the Boss compact catalog. The OC-2s were originally housed in much lighter brown enclosure with the label “Octaver” on them. The name changed to “Octave” in 1984, meaning that the original ones were manufactured in japan from 1982 to 1984. These first issues are nowadays highly sought after and in one word, rare. And in another, expensive. The board on this unit is definitely a later revision. There’s not much left from the old school japanese design, and has been replaced with modern autorouted feel on overall board.

Boss-OC2-guts1

There’s a schematic with good semiconductor listings up at Hobby-Hour.com and you should check it out. This same page shows also the original board layout with original traces. There are one single  and one dual flip-flop IC on the original board design, but that has changed on later revisions. As we can see, the board of this 2001 unit has two CD4013 chips in the lower right corner of the board. There are other changes in the layout too, so the differences between a 1982 unit and this one are more than just minor.

Boss-OC2-guts2

The two octaves down are using two channels of the flip-flops and the one down is using one. So the leftover one on the modern board is unused. How do these changes affect the tone? Don’t have a clue as i haven’t had the pleasure of comparing the modern one with the original design. Features are quite simple. We have three knobs which control the levels of clean, buffered signal, one octave down and two octaves down. There are two opamp channels driving each down octave settings. These controls maxed will result in wild, not so good tracking of the down octaves. The analog feel is strongly present.

How does it sound?
The tones this one produces are very good. Where as most old school down octaves tend to feel low on down octave levels, this isn’t a problem for OC-2. The tracking on OC-2 is also very respectable. Although, once the octaves are maxed, the guitar signal still feels a bit weak to keep the octaves in tact, resulting in brain melting, uncontrollable mistracking. Paired with a compressor before OC-2 will help to keep the tracking in line. While we’re at it, a fuzz of distortion before this will also give out very nice results. I think the most well known instances of hearing OC-2 in action are the CKY albums from the 00’s.

To sum it up. This is the octave effect to have. Even though OC-2 was discontinued in 2003 and replaced by more modern OC-3, the cult reputation and usability of this all analog down octave monster is well warranted. Definitely one of the best Boss boxes around.

Boss ML-2 Metal Core

Friday, August 22nd, 2014

Boss-ML2

What is it?
Boss ML-2 Metal Core from compact series. Made in taiwan in january 2009.

Sure, i was interested in this due to its reputation. This is supposedly the meanest metal distortion there is and i’ve heard good things about it from people who i share a lot of opinions on sounds. So i grabbed one. I’ll get to the sound part later, but even though i agree on pedal tones with only few people.. This isn’t one of those where i agree. This unit took me by surprise. First question mark rose when i opened the bottom plate.

Boss-ML2-guts1

And the second one when i turned the board over. I would have never guessed by the demos and the praises i’ve heard that this would be a digital distortion. Constructed in the most boring way with all SMD and powered by what appears to be Roland branded DSP processor. The crystal clock is placed right beneath it. There are a couple of 1458 opamps in there too, but most of the design goes way over my head.

Boss-ML2-guts2

As for controls we have standard level and distortion knobs in addition to high and low controls. I’m not sure what the designer was after and why this design ended up this way. Maybe it was to recreate the designs that became classics by updating them with a digital counterpart? The EQ may be the best part of the circuit, but…

How does it sound?
I’m sad to turn to my prejudice on digital drive designs, but this time it is warranted. Even though the EQ controls try their hardest to mimic the gyrators of HM-2 and HM-3, the crushing and soaring this one tries to produce makes me feel uncomfortable. There is enough gain and while marketing suggests this to be answer to modern, next generation of metal players tonal needs, i can’t do anything else but disagree. Metal distortion, yes. Good sounding one? No. The sharpness and unnatural honk of all digital and/or modeling drives is present. No wonder guitar music is at its all time low.

Paired with a delay and used for those 80’s german detective tv series anthems – maybe (Although, you’ll get closer to that with Digitech RP-6). For anything else? Try HM-3 or MD-2.

Boss RV-3 Digital Reverb/Delay

Tuesday, August 19th, 2014

Boss-RV3

What is it?
Boss RV-3 Digital Reverb/Delay from compact series, made  in taiwan. Serial number on grey label points to june 1991. But since the units were apparently manufactured from 1994 to 2002 and the label was changed from pink to grey in early 1999, i think it’s safe to assume this follows similar error on serials as early taiwanese HH-2 Heavy Metals – being a decade off. This would mean that this unit is really manufactured in june 2001. Which makes a lot more sense.

RV-3 is a second generation of Boss digital reverb pedals. Sharing the color with the ground breaking RV-2, but housed in standard compact pedal sizes enclosure. As it’s predecessor, the full blown SMD design was expected. Where the RV-2 had two boards stacked the RV-3 has only one. It is as tightly packed on both sides though. The circuit footprint is way smaller and the features are doubled. Who doesn’t like to live in the future.

Boss-RV3-guts1

There’s a schematic up at FIS, if you’re interested. It shows pretty standard buffering and mixing with simple splitting for the stereo outputs. The digital part creating the reverb behind the mixing is pretty complex. Apparently the same digital setup can be programmed to do other things in addition to reverberation. The schem has “PS-3” printed on it, so my guess is that they have been using the same board for these two different effects. Maybe even more pedals share the same DSP architechture.

Boss-RV3-guts2

Board design is very modern looking. There are 11 reverb and delay modes with reasonable controls over the main parameters. Mix control for all modes. Time and feedback controls for the delays and reverb time with tone to control the high end damping of the reverbs.

How does it sound?
Very good with lots and lots of usable modes and the stereo output also adds to the usability. The digital signature that usually takes the edge off from so many designs is practically nonexistent. It’s not harsh sounding but a lot closer to natural. There’s even a feel of the expensive rack mount effects present. Wouldn’t call it “warm” or analog-like, but still pretty good. Most negativity comes from standard Boss facelessness. Not too personal and not the greatest pedal ever made – but still. Very very good. And this will see use as it’ll suit many situations of use, easily.

Boss PSM-5 Power Supply & Master Switch

Thursday, August 14th, 2014

Boss-PSM5

What is it?
Boss PSM-5 Power Supplu & Master Switch. Made in japan, november 1982.

There has been a time place for everything. Daisy chaining, or dedicated power supplies were both practically unheard of until this new and exciting device hit the market. What surprises me more is that the pedal was actively sold from 1983 all the way until 1999. I thought the interest for the features offered would have been way gone by 1999. This unit has seen use and it has the orginal black label on its bottom. The label explains the main features as well.

Boss-PSM5-back

The nice looking old school style board houses the boss standard flip-flop switching and an effect loop (’cause that’s what the pedal actually does). These were originally shipped with a power supply and a splitter cable for up to seven effects. Since my specimen is from the year 1982, you can take a guess if either of those have survived. Quick search produced a schematic, which confirms that the design for the loop is simply four buffers, controlled by electronic switching – an effect loop if you will. Schamatic also shows that the power supply is only splitted for the out going 9VDC.

Boss-PSM5-guts1

One other thing noted in the schematic. The operational amplifiers should be NJM4558DD, or in other words the classic JRC4558D. Seeme like mine has been modded at some point in the pedal’s life. The ICs have been removed and replaced by sockets, which now have two LF353s, high grade audio chips in them. Rest of the semiconductors seen on the board are two BJTs for the flip-flop, another two BJTs for LED control and four JFETs to take care of the actual switching of the loop.

Boss-PSM5-guts2

These older Boss boards are mostly a pleasure to look at. Acid trip traces but annoying lack of symmetry. Plus an acre of free land to grow your tomatoes.

How does it sound?
It works as an effects loop, so it should not have a sound of its own. And furthermore, it doesn’t. I do understand why someone wanted to swap the opamps for “better” ones, but as they are acting only as an unity amplifiers (or we could say buffers), i strongly feel the improvement in sound is next to nothing. This being there’s not much i can say about how it sounds. It is a relic, which makes it rather interesting.

I do believe this had lots and lots of user value back in eighties and in the beginning of 90s. Using one now? Not a chance. There are tiny hardwired true bypass loopers and extremely high quality standalone buffers in existence, so at least for me, the choice would be very simple and clear.

Boss TU-2 Chromatic Tuner

Tuesday, August 12th, 2014

Boss-TU2

What is it?
Boss TU-2 Chromatic Tuner from compact series. Made in taiwan, june 2004

The workhorse. I’ve heard stories that these nearly didn’t make it to production at all, since the designers were sure that there would be no market for a pedal tuner. Well. I do get it. After all, the Arion and DOD had flopped pretty hard with theirs. But the TU-2 made it to production and if i’m not completely wong, it sold very well. So well that Bossarea page calls it an instant hit.

Boss-TU2-guts1

There are different tuning modes as features, but i must confess that i’ve never used any of those. Not even to try them out. The standard chromatic mode that picks up the note you play has been sufficient. For years.

Pedal is made of two separate boards, a mix of digital and analog circuitry. Nothing too eye pleasing with autorouted, tasteless and scentless feel to overall construction.

Boss-TU2-guts2

But then again, who buys a hammer for its looks? Metaphor for a hammer isn’t as far as you would think. As you probably have seen, there are pink and tiny designer hammers in existence, but no one in their right mind would pick up one of those if they were to build a proper wooden wall. No. They would pickup that old, rusty heavy thing that is a real hammer.

Boss-TU2-guts3

Boss TU-2 is (or was) a hit for several reasons. User can see the display on the darkest stage without disturbance, the accuracy is good enough and.. Well. It simply gets the job done. TU-2 got discontinued due to TU-3, which has more features and, i believe, is aimed to take on TC Electronics tuners in the market, which consequently have even more features. Come what may, the TU-2 will stay and enjoy its cult status. Less features sometimes mean higher usability.

How does it sound?
As most of the Boss pedals tend to drain your signal when bypassed, the buffering on TU-2 is either better than on the rest, or i may be turning def. While this tuner doesn’t sound like anything per se, it acts a faithful buffer when it’s turned off. As a tuner, this unit is something that all other pedal tuner manufacturers should take a look at. It works.

Boss HM-3 Hyper Metal

Sunday, August 10th, 2014

Boss-HM3

What is it?
Boss HM-3 Hyper Metal from Boss Compact series. Made in taiwan, march 1993.

The younger brother of since discontinued HM-2. Similar controls and expectance for similar sounds was high to say at least. This time there is some symmetry on the board design and even those machine like autorouted traces do not bother me that much. Not exactly sure how accurate the schematic up at FIS is, but i’m thinking the base topology is correct. So we have a design that’s somewhat close to HM-2, with the triple gyrator EQ tha has two controls and three separate clipper stages.

Boss-HM3-guts1

As usual for many Boss boards, the opamps are SIP devices. The asymmetrical clipping amp with distortion control is made of one opamp channel and NPN/PNP transistor pair. Still quite similar to the HM-2. In build quality and and housing issues, this doesn’t stand out of Boss Compact crowd. Solid, but dull.

Boss-HM3-guts2

All of the features feel a lot like HM-2 Heavy Metal, but power supply requirements are updated to be more modern and well..

How does it sound?
Actually better than the praised older brother. To my ears the distortion is slightly thicker, fatter and lows feel even more crushing with its soaring highs. The overall tone manages to stay quite defined even thought the amount of distortion is impressive. If i was to use metal distortion on my board, this would most likely be it.

Boss HF-2 Hi-Band Flanger

Wednesday, August 6th, 2014

Boss-HF2

What is it?
Boss HF-2 HiBand Flanger from compact series. Made in japan, august 1988.

Japan made HF-2 is probably the most praised flanger, not only in Boss catalog, but otherwise too. While the “standard” Boss flanger may be and have been the BF-2 for decades, the HF-2 operates in slightly different manner. While most flangers mix the whole incoming signal with delayed duplicate (controlled by LFO to create the sweep), this Hi Band Flanger takes the incoming signal and splits it in two ways. Other stays as it is and the other is pushed to up octave which then has the flanging delay mixed into. Or so they say. That idea sure has some out of the box thinking in there.

Boss-HF2-guts1

The board is full and still looking rather pleasing. The old school board manufacturing methods always please the eye. The delay section of the flanger isn’t anything special. It ihas MN3102 for the clock and MN3204 512-stage Bucket Brigade Device for the delay. The schematic is available for download through the interwebs. Looking at schematic, i’m not exactly sure how that half of IC2 and Q2 are supposed to create the clean octave up, but it surely won’t act only as a buffer in front of the delay circuitry.

Boss-HF2-guts2

That being said, the HF-2 isn’t your standard flanger, but it isn’t anything too special either. Controls are very sufficient. Manual affects the Rate and Depth, while Resonanse controls how much delayed, or flanged signal is getting in the mix with original signal. The footprint is pretty common with most flangers and choruses.

How does it sound?
Don’t be expecting anything too wild. It is a very nice sounding flanger that goes from mild detuned vibrato to airplane hights. Overall tone is still rather tasteless and scentless, the same problem we’re facing with many Boss boxes. Sure it sounds good, but it doesn’t quite reach that acidy velcro flanger wildness the greatest flangers reach. It does offer slight variance to most usual flangers, which is a good thing. Controls offer good variance in terms of speed and depth. For me, the best use for this is to have it act as a vibrato. I do get whyt some folks prefer this over any other, but that isn’t me. Good but somewhat boring.

Boss CE-3 Chorus

Sunday, August 3rd, 2014

Boss-CE3

What is it?
Boss CE-3 Chorus, made in taiwan, august 1988.

Boss choruses are all praised, even though the CE-3 has less reputation if compared the obvious classics like CE-1 and CE-2. With less reputation comes a less numbers on the price tag on auction listings. This particular unit is one of the very first CE-3s to come out of taiwan plant. CE-3 is the first Boss chorus with stereo output and there are couple of interesting things on the pedal. Like the position of the three knobs. Bossarea has more information listed.

Boss-CE3-guts1

Board design is pretty with old school traces, but disturbing asymmetry on the layout. There is a schematic up on Synthdiy. Design is pretty common with two 4558s to drive the signal after the FET buffer and after the BBD modulation stage. The modulation stage is based on MN3207, a 1024 stage analog bucket brigade device. That chip is controlled by a MN3102 clock. Rate and depth are controlled by LFO, constructed with one TL022.

Boss-CE3-guts2

Stereo operation can be used to push zero and reverse phases to their own outputs, like many modern stereo choruses.

In general, everything about this unit is great. Vintage feel to the design, construction and it even offers some eye candy being as ugly as it is. And the most important part is yet to come..

How does it sound?
Soft and natural chorus. May not be as mellow and 70’s sounding than CE-1 and CE-2, but there isn’t that cold harsh detune around that, at least in my opinion, kills the usability of countless chorus designs. Depth control is sufficient, but i was surprised how slow the Rate is, even when maxed. This is a feature that makes the unit have a soul of its own.

Definitely one of the best sounding vibe-like chorus pedals in the price range.

Boss PS-5 Super Shifter

Friday, August 1st, 2014

Let’s do a month with Boss pedals only. Why? Because i can. Starting the Boss august with PS-5 Super Shifter…

Boss-PS5

What is it?
Boss PS-5 Super Shifter from Compact series. Made in taiwan in april 2008.

To begin with. As usual, i ran the serial number through the Bossarea.com serial number decoder. This is something i always do whenever i get a new Boss pedal for my collection. Of course i keep a list of all the Boss pedals in separate text file. Now this wouldn’t be anything interesting, but as the current collection is, i placed the PS-5 next to PH-3 on my list. I must have been slightly tired, but i couldn’t make a clear difference between the rows for PS-5 and PH-3 (ok, i always read/edit the list with an editor that uses fixed font). The reason i got confused for a second was that these both units are made in Taiwan and in april and in 2008. Plus when you think about the list with nicely tab formatted text, you’ll know the rows will have a lot in common. Super vs. Phase, PS-5 vs. PH-3 and the dates.  Anyway. Got this in a trade about couple of weeks later of when i first realized that i don’t have any dedicated “Harmonizer”, or “Pitch Shift” effects in my collection. Wasn’t actively looking to get one, but it just happened. The guy trading it told me that he thought it was a nice effect, but he didn’t seem to use it much.

Boss-PS5-guts1

Opening the bottom plate showed nothing of any surprise. A board filled with tiny SMD components and so many “via”s that i lost count after the first 15 seconds. (For those not familiar with what i’m talking about – the vias are tiny holes on the board that are meant to take the connection to the other side of the PCB.) Flipping the board over continues with the same. A few big digital chips and a few operational amplifiers. Not my closest target for affection, but clean and neat nevertheless.

Boss-PS5-guts2

Which means that i’m not able to discuss the design at the moment. Yup. I simply don’t understand it well enough. There isn’t a schematic available, but the user manual is rather interesting read.

The unit is very feature packed. At first i thought the features just look like a lot and the up shifting is the main deal. No. That’s not it. I’ve been only playing around with this unit for a few hours since i got it, but mixed lightly on the balance pot and finding the tuning and a scale. That’s how it starts. It’s basically Boss’ answer to Digitech’s Whammy if you take a expression pedal and attach it to the PS-5. That plus all the static settings.  There are two features worth mentioning, even after all that. The “T. Arm” mode. The stomp acts as a momentary switch when this mode is on. This way one can get a digital reproduction of a tremolo arm function that comes naturally with Stratocasters. The last mode is “Flutter”, which is another digital reproduction of the thing most of us do with a tremolo arm. The features are pretty complex, so i’ll just leave you with that. And the link above to the manual.

Sadly, these features leave a slightly bitter taste. The question that rises, is this supposed to be a real, usable professional tool or just a toy to play around with? Other than that, it feels rather solid.

How does it sound?
The reason that guy didn’t use this much? I too was a bit put off by the number of features at first. There is a harsh digital feel to the most sounds this spews out. But i found the pitch shifter feature to be gold. Once the right extra pitch for the scale and the reasonable balance is set, this circuit sounds very good and nearly natural – despite all the digital harshness. Placing a fuzz after this will take a lot of the digital signature away and well, it’ll sound next to awesome.

In all, there are way too many different types of sounds to say exactly how this sounds. Some of the features sound very good and they have a purpose. Others are just picture clear resemblance of some plastic Tomy My First Effect Pedal toy. Toy aspect doesn’t feel too good, but there are a lot of usable range on the controls. If the user knows the pedal well enough, it may be a nice tool on a studio desk. Maybe the designing engineers tried just a bit too hard on this one.

Boss SYB-3 Bass Synthesizer

Friday, June 13th, 2014

Boss-SYB3

What is it?
Boss SYB-3 Bass Synthesizer. Made in taiwan, september 1999.

This is one of the pedals that have stayed with me for a long time. Got it somewhere around 2002 and i’ve used it mostly with a guitar with occasional bass hook when recording. Due to its very complex digital design, i won’t be able to break the design down. So i’m forced to leave you with an overview of the features and aesthetics. Opening the bottom plate reveals a two sided PCB that is pretty crammed. On the board design, there’s not much to mention. It’s your standard SMD-board with focus on functionality, rather than aesthetics. Like most Boss boards. I’d say it’s dull.

Boss-SYB3-guts1

Bottom layer is for caps and resistors. The upper sider has all the semiconductors. As you can see, the number is quite high. The reason for the complexity? Well. It has eleven modes, ranging from “internal”, made up digital synth-like sweeps to standard, clean autowah sweeps. As the controls go, there are individual level settings for clean and synth signals, which gives you the option of blending the signals the way you want – all wet being rather wild. Next up is a very synth like filter with frequency and resonance controls. If there was one thing i’d like to see added to this one, it would be a expression pedal input for either of these controls. After these, there is sensitivity and decay controls that control how the trigger performs.

Boss-SYB3-guts2

Last control is 11 position switch that sets the effect type. Types are “internal” from settings 1-7. These are the programmed synt-like sweepers that are more or less unique to the pedal design. Settings 8-9 are “W-shape” modes, which are closer to standard autowah sounds than the internals, but still something rather odd. Last two settings are for “T-Wah”. So its safe to assume the last modes are digital recreations of ye oldee boss T-Wah autowah/envelope filter. Haven’t been able to play with original T-Wah, but something tells me these modes are a bit wilder or tighter than the ones found on the old analog pedal.

Either way. There is a ton of versatility. I’d label this as one of the top ten Compact serie pedals. When Boss engineers take a design over the top, the results are still usable.

How does it sound?
Wicked. Extreme envelope filter on steroids. Wild filter sweeps with great, completely unnatural synth-style modes. Of course, there are milder autowah settings available, but it’s the wild ones that will roll your socks. The blend controls give the possibility of nice, subtle effects too. Very versatile and fun effect. Maybe the tones offered aren’t the greatest thing for your base sound, but for those hidden hooks and shock effects.. This is the right stuff.